The item you're looking for might have been renamed, removed or relocated.
These are page(s) found with similar content.
- Water Cylinder Wrapper Production LineThis line of machinery is capable of producing a 'Completed water cylinder wrapper' of 480mm to 580mm x 686mm to 1942mm long, by means of a two-piece construction from coil.
- Turbulator Cut Form & Stuffing Production LineThis line of machinery is capable of cutting to length, forming and stuffing a 0.08mm aluminium Turbulator product into a steel sleeve automatically from coil at a production rate of greater than 2000 per hour (based upon a 555mm product). Simple length variation can be achieved between 300 and 800mm.
- Tensioning Band for ChimneysThe Following machinery will accept pre cut-to-length blanks of 0.5mm stainless steel and form into the tension bands at a speed of 20m/min.
- Slip On Flange Production LineThis line of machinery is capable of producing three profiles namely- 20mm Slip-on Flange (0.6/0.7) thick, 30mm Slip-On Flange (0.7/0.9) thick, 40mm Slip-On Flange (0.9/1.2) thick from 1000kg coils of galvanised mild steel in cut lengths from 100mm to 5 metres.
- Retainer Ring Production LineThe following line of machinery is capable of producing a 'U' shaped ring from coils of 28.14mm wide x 2mm thick stainless steel at a roll forming rate of 25m/min less stoppage to cut time.
- Plain Seam Panel LineThe Plain Seam Panel Line is capable of processing 1250mm wide coils of 0.6 to 0.8mm Plastisol steel, face side up, into up to 7.5 metre lengths of LH, RH or L & R hand plain seamed sheets.
- Picket Section Production LineThis line of machinery is capable of forming the punched and sheared 15mm x 14mm Picket Section Channel in lengths from 470mm to 6000mm from coils of pre slit-to-width 1.2mm mild steel.
- Oval Seamed Tubular DuctsThis line of machinery is capable of producing oval seamed Tubular Ducts in cut lengths up to 10m long from pre slit-to-width coils of 0.4mm thick galvanised steel at a rate of 25 m/min less cutting and flaring time i.e. approximately 20 m/min.
- Mill standMill Stand machines are for forming products 60mm high or above. Each pair of top and bottom rollshafts is individually carried on sealed for life ball bearings within the adjustable bearing blocks of the individual cast support stand.
- Fixed SideplateFixed Sideplate machines provide a durable, cost effective means of roll forming sections up to 60mm high from most metals up to 3mm thick at speeds of up to 35m/min.
- Filter Bag Header MachineThis line of machinery is capable of producing your V notched end tabbed and pierced Bag Header Lipped frame profiles in widths of 16, 20, 22, 25, 30, 45 and 47mm x 17mm high, from coils of 0.5mm galvanised mild steel.
- Damper Blade LineThe following line of machinery is capable of producing the one-piece, clinched 50mm Damper Blade from 1000kg coils of 0.5mm galvanised mild steel, 430 stainless steel, and 316L stainless steel in cut lengths from 80mm to 2-metres.
- Cold Store Panel LineThe following machinery is capable of producing variable length, variable width coldstore panels from pre-cut to size blanks of 1 metre to 6 metres in length.
- Cable Core Segment Production LineThis line of machinery is capable of producing the range of ELR, HS, LR, HM & MR 036 type segments in lengths from 4 to 16 inches, from coils of 0.85/0.95mm thick DC01 steel, at a rate of approximately 4m/min.
- Bearer ChannelThe following line of machinery is capable of producing the size 320 to size 1520 punched, printed and formed Fast Track Bearers in 100mm length increments from coils of 1.94mm thick galvanised mild steel at a rate of approximately 8m/min and presenting them in stacks of 10 on their side to be removed.
- Anti-Sag Bar Production LineThe following equipment is capable of producing end cropped, end punched and rollformed Anti-Sag Bars from pre slit-to-width coils of 1.6mm thick S450DG structural steel in Lengths of 350 to 2000 +/-1mm at a rate of 9 to 18 metres per minute, dependent upon the length.
- Up Down Cobra CurverThis machine is capable of automatic bi-directional curving of 100 to 150mm wide x 8 to 20mm thick mild steel plates into various bi-directional curved shapes at a speed of approximately 5m/min.
- TruTool F 301The TruTool F 301 seam locker is the perfect choice if you process sheet thicknesses of 0.45 mm 1 mm mild steel. For straight or curved ducts.
- TruTool F 300You can use the TruTool F 300 seam locker to work in sheet thicknesses of 0.75 mm 1.25 mm mild steel and lock straight as well as curved ducts.
- Silencer Sleeve Forming MachineThe following machine is capable of accepting hand fed pre-cut to size blanks of 0.7mm thick stainless steel or 0.5mm thick titanium and automatically forming a pre determined Silencer Sleeve profile at a rate of one every 40s.
- RollformingOur Roll forming machines are generally split into 4 different types. All types provide rapid, continuous production of your cold-formed sheet steel components in any length. Machines can be fed from coil as part of a line or in their simplest form they can be strip-fed or sheet-fed roll formers.
- Ring and cylinder rollingRing rolling is the action of curving a section into a segment or a circle is frequently achieved as a continuation of the roll forming process. Cylinder rolling is our 2 roll bending machinery forms virtually Flat Free cylinders or segments from flat blanks in one pass.
- Ring and Strap MachineProduces two seperate products form stainless steel coil, processes include cropping, punching, no loss shearing, ring rolling and piercing.
- Rafted & CassetteRafted, cassette or cartridge rollforming machines are ideal where production lines demand rapid tooling change.
- Paper Backed Metal Lath Production LineThe 27 wide lath produced had a strand width of 0.051 with 84/85 diamonds, 17.5mm long approximately.
- Metal Lath Production LineThe 2440 long x 700 wide lath produced has a strand width of 1.3mm with diamond size of 20 x 10mm in material gauges from 0.4 to 0.8mm. The production rate of this line is 20 sheets per minute.
- DuplexDuplex machines have twin roll forming heads to provide variable width rolling of double-edged panel products at speeds up to 30m/min.
- Drive Cleat Duct LineThis Drive Cleat Duct Line is a compact straight line machine for forming Drive Cleat profile ducts with a Pittsburgh duct seam.
- Automated metal formingThe continuous nature of roll forming can be extolled by incorporating other processes such as ribbing, piercing notching, shearing, cropping, ring rolling or folding. This produces an efficient, compact production line from coil or blank, which may include offload or shearing of the completed product.
- 20s pittsburghThe 20's Pittsburgh rolls are fitted as standard to one side of the 5 stage machine with the option to fit 1 of 3 cnc machined roll sets to the outboard extension shafts.